1. Key points of solid wood floor maintenance
1. The floor should be laid in the later stage of construction and shall not be cross-constructed. after laying, it should be polished and painted as soon as possible to avoid soiling the floor or causing damp deformation.
2. Before laying the floor, it is appropriate to unpack and pile it at the laying site for 1-2 days to make it adapt to the environment so as to avoid expansion and shrinkage deformation after laying.
3. Moistureproof measures should be taken for laying, especially in humid situations such as the bottom layer. Moistureproof measures are coated with moistureproofPaint, lay moistureproof film, use bedding treasure, etc.
4. The keel should be flat and firm and should not be used.Cement reinforcement, it is best to use expansion bolts, beauty nails and so on.
5. The keel should choose Larix gmelinii, Liu'an and other wood with strong nail grip. The moisture content of keel or hairy floor should be close to that of floor. Keel spacing should not be too large, generally not more than 30 cm. Both ends of the floor should be placed on the keel, not empty, and nails must be nailed on each keel. Do not use water-based glue.
6, the floor should not be too tight, there should be enough expansion joints around, and should not be ultra-wide laying, in case of wider occasions should be separated and cut off, and then press the copper bar transition.
7. Floors and halls, bathrooms, kitchens and other stone floor junctions should be thoroughly isolated and moistureproof.
8. Floor chromatic aberration is inevitable. If there is a higher requirement for chromatic aberration, we can sort it in advance and adopt the method of gradual transition to reduce the sense of sudden change in vision.
9. Avoid washing with water in use to avoid long-term sun exposure and continuous direct blowing of air conditioners.The window prevents rainforest and hard objects from hitting and rubbing. To protect the floor, the paint can be waxed.
II. Maintenance of bamboo floor
Correct use and maintenance is the key to prolong the service life of bamboo flooring. In recent years, some users have complained about some quality problems caused by improper use of bamboo flooring. In this case, it is necessary for dealers or enterprises to do a good job in after-sales service. At the same time, it is also necessary to publicize the knowledge of use and maintenance to consumers.
Bamboo flooring should pay attention to the following points in use:
The main results are as follows: 1. Although the indoor dry humidity bamboo floor is dried, the change of size is reduced, but because the bamboo is a natural material, it will also be deformed with the change of climate. In the dry season in the north, especially in the openWhen heating, the indoor temperature can be adjusted by different methods, such as using a humidifier or putting basin water on the heater; in the yellow mold season in the south, open windows and ventilation to keep the room dry. To this end, indoors should try to avoid sun exposure and Rain Water wet, in case of water should be timely dry.
2. Avoid damaging the floor surface, bamboo floor paint, hard objects, sharp scratches, metal friction and so on.
3. Correctly clean the floor in the course of daily use, keep the floor clean, clean it with a clean broom, and then use a wrung-out mop to take on a new look. If conditions permit, it is better to wax the floor once every two to three months.
Third, the cork floor maintenance
The maintenance of cork floor is easier than that of other wood floors. in the process of use, sand should be avoided during the day, and individual sand will not affect wear and tear, so when sand is brought in, pressed into the foot and pressed into the elastic layer, when the footsteps leave, it will be ejected again. Of course, I would like to remind you here that it is not appropriate to bring in too much dirty sand, it will produce flow wear and tear. Therefore, although it is affected by the sand, too much sand will wear out. Therefore, the sand brought into the room should be removed in time, and there is no need to be equipped with vacuum cleaners. There is no need to worry about damp warping, mildew and other phenomena.
Five years later, if there is wear elsewhere, it can be locally used to make up, that is, re-add the coating on the part, the method is very simple, gently polish with sandpaper at the wear place, remove the dirt on the surface, and then gently wipe it off with a dry soft cloth, re-coat the coating, or apply polyester film locally.
IV. Cleaning and maintenance of composite wood flooring
Usually you can use a vacuum cleaner or broom to clean the surface dust, and then wipe the floor surface with a wet rag or mop that is wrung dry without dripping. After mopping the floor, it is best to open the doors and windows to let the air circulate, or you can blow with an electric fan to dry the floor as soon as possible. In addition, to avoid damage to the wear-resistant layer of composite wood flooring, otherwise the moistureproof function and brightness of the floor will be affected. Try to wear cloth slippers when walking on the floor.The feet of furniture are affixed with a soft bottom protective pad to avoid the "feet" of furniture scratching the floor wear-resistant layer, do not let heavy objects break the wear-resistant layer. Do not use sandpaper, grinders, steel brushes, strong decontamination powder or metal tools to clean the composite wood floor. If you have a cat at home, you should find a way to solve the damage to the cat's claws. It is recommended not to wax.
Pay special attention to:
1. Never use water to wash the floor.
2, can not use corrosive detergent to clean the floor, wear-resistant layer is aluminum trioxide, it is amphoteric oxide, can react with acid, but also can react with alkali.
3. To avoid alkaline substances, it is a good way to scrub with rice washing water.
4. Avoid sanding, waxing or painting the floor with sandpaper.
